Split AC Re-Installation Services
When your Split AC needs to be shifted, replaced, or re-mounted after renovation or relocation, our Split AC Re-Installation service ensures safe dismantling, correct placement, leakage-free gas handling, and full performance restoration.
About Our Split AC Re-Installation Service
Split AC re-installation is more than just mounting the unit back on the wall. Incorrect piping, poor vacuuming, wrong drainage slope, or careless electrical reconnection can lead to gas leakage, water dripping, poor cooling, and compressor damage. Our professional split AC re-installation service ensures your unit is safely dismantled, relocated, re-mounted, vacuumed, gas-balanced, and tested for full performance. Ideal for offices shifting locations, post-renovation setups, layout changes, and equipment upgrades.
Safe Dismantling &
Re-Mounting
Your AC is removed and installed without gas loss or physical damage.
Leak-Free Gas
Handling
Proper vacuuming and pressure testing ensure zero leakage.
Cooling Performance
Restored
Final testing confirms correct airflow, temperature drop, and load balance.
What’s Covered in Split AC Re-Installation
AC
Dismantling
- Electrical power isolation
- Controlled refrigerant locking
- Indoor and outdoor unit disconnection
- Pipe insulation safety handling
- Mount removal
- Drain pipe disconnection
- Transport readiness preparation
- Physical damage check
New Location
Installation
- Wall strength inspection
- Correct indoor unit alignment
- Outdoor unit placement with vibration pads
- Stand or bracket fitting
- Proper spacing for airflow
- Drain slope correction
- Pipe routing adjustment
- Insulation sealing
Piping, Vacuum &
Gas Balancing
- Copper pipe connection
- Proper vacuum creation
- Pressure testing
- Leak detection
- Refrigerant balancing
- Oil stabilization
- Expansion valve coordination
- Temperature drop confirmation
Electrical & Drain
System Setup
- Correct power connection
- Earthing safety check
- Capacitor check
- Remote sensor testing
- Drain pipe leakage test
- Backflow prevention check
- Moisture risk elimination
- Final safety validation
What’s Not Covered
To avoid confusion and disputes, the following items remain outside re-installation service:
- New copper piping supply
- New electrical wiring
- Wall core cutting or drilling
- Stand fabrication
- Gas refill due to pre-existing leakage
- Control board or thermostat replacement
Note: Additional materials and electrical work are chargeable after site confirmation.
Service Level Agreement (SLA)
Clear SLAs build trust by setting transparent response times and clear support commitments clients can rely on.
Critical issues
Response within 4–8 business hours
Non–critical issues
Response within 24–48 business hours
Visit timing
Business hours. Mon–Sat
Escalation path
Technician → Supervisor → AMC Manager
How Our Split AC Re-Installation Works
We check new wall strength, drainage slope, piping distance, outdoor unit placement, power access, and airflow clearance.
Refrigerant is safely locked, electricals disconnected, piping sealed, and the unit is packed to prevent physical or internal damage.
Indoor and outdoor units are installed with correct spacing, vibration pads, and airflow clearance to ensure proper heat exchange.
Deep vacuum removes moisture and air. Refrigerant balance is restored for optimal cooling efficiency and compressor safety.
Cooling output, temperature drop, water drainage, vibration, and noise are tested before final handover.
Deliverables You Receive
- Re-installation job completion report
- Gas pressure and vacuum record
- Electrical safety validation
- Drain flow test confirmation
- Final cooling performance status
- Usage and maintenance guidance
Why Choose Us for Split AC Re-Installation Services
We dismantle, shift, and reinstall Split AC units without gas loss, water leakage, or vibration issues, so you get clean installation and original level cooling performance.
Damage-Free Dismantling
Your unit is removed without gas loss or physical damage.
Correct Drain & Slope Setup
We prevent future water leakage through proper drainage alignment.
Gas Vacuum & Pressure Control
No moisture, no air, no cooling drop after installation. Everything stays stable.
Vibration-Free Outdoor Mounting
We eliminate rattling, noise, and long-term bracket damage.
Final Cooling Output Verification
You don’t just get installation, you get confirmed performance.
Safety and Compliance
We follow gas handling safety rules, electrical isolation protocols, PPE usage, and wall-load guidelines to eliminate risk to people, property, and equipment.
Book Your Split AC Re-Installation
Shifting office or changing layout. Use this form to plan safe dismantling, shifting, and re-installation of your Split AC units without gas loss, leaks, or cooling issues.
Need quick help before you submit?
Quick Highlights:
- Safe dismantling and packing of units
- Correct indoor and outdoor placement
- Proper drain slope to avoid water leakage
- Vacuuming and pressure balancing
- Full cooling and noise check after install
- Option to combine with general servicing
No obligation: We review your site details and suggest the safest, most cost effective re-installation plan.
Start Your Split AC Re-Installation Request
FAQs
1. Can my existing gas be reused during re-installation?
Yes. If there is no leakage and gas is safely locked, refilling is not required.
2. Why is vacuuming important during re-installation?
Vacuuming removes moisture and air, preventing compressor damage and cooling loss.
3. Will water leakage occur after re-installation?
No. Proper drain slope and flow testing are done before final handover.
4. Can re-installation reduce my cooling performance?
If done incorrectly, yes. That’s why vacuuming, pressure testing, and alignment are critical.
5. Is Split AC re-installation included in AMC?
No. It is handled as a separate service but AMC clients may receive discounted pricing.