Floor Standing AC Installation (3 AC)

About the Service

Our Floor Standing AC Installation Service for 3 Units is built for large commercial environments such as showrooms, offices, malls, restaurants, gyms, studios, banquet halls, warehouses, and any large spaces that require multiple high-capacity tower ACs installed in a single appointment.

Floor standing ACs are heavy-duty commercial machines with large compressors, high electrical load, long piping requirements and complex airflow planning. Installing three tower AC units together requires precise coordination, accurate measurements, and commercial-grade technical expertise.

This service ensures a safe, efficient, and fully standardized installation of 3 tower ACs in one visit, following all brand and safety guidelines.

Ideal For

• Setting up 3 tower ACs in newly designed commercial spaces

• Replacing old cooling systems with multiple high-capacity units

• Cooling large halls, open office floors, gyms & restaurants

• Shifting 3 AC units to a new location

• New business setups requiring strong cooling output

Our Process

1. Pre-Installation Site Survey for All 3 AC Units

We inspect the entire area to determine the perfect placement for all three units:

• Cooling load calculation

• Individual & combined air throw direction

• Floor spacing and stability

• Power load distribution for all 3 units

• Copper piping route planning

• Drainage points

• Outdoor unit space management

• Tonnage analysis (1.5 ton to 5+ ton each)

Ensures equal cooling performance and long-term safety.

2. Placement & Alignment of 3 Floor Standing Units

• Units placed at strategic points for uniform cooling

• Proper spacing between units

• Ensuring vibration-free and level alignment

• Optimized airflow without obstruction

• Professional layout planning for high traffic commercial areas

3. Copper Pipe & Insulation Setup for All Units

For each AC unit:

• Copper piping connected between indoor & outdoor units

• Thermal insulation applied

• Strong and leak-proof flare joints

• Organized and clean pipe routing

• Additional copper, drain pipe, or bracket requirements explained transparently

4. Electrical Wiring & Power Load Safety

All three AC units require accurate electrical configuration:

• Load balancing for 3 heavy-duty machines

• MCB & wiring compatibility check

• Secure terminal connections

• Voltage & ampere testing for each unit

• Earthing verification

• Overload protection recommendations

Commercial installations require stable power distribution — we ensure all 3 units operate safely.

5. Individual Drain Line Setup for Each Tower AC

• Separate or combined drain lines based on layout

• Proper slope for uninterrupted water flow

• Leak-proof joints

• Checking for backflow or blockage possibilities

Prevents water accumulation and leakage issues.

6. Outdoor Unit Placement / Mounting for 3 ODUs

We install and position three outdoor units:

• Proper airflow clearance around each ODU

• Vibration-absorbing base support

• Weather safety considerations

• Height-based installation (if required)

• Secure mounting and connection

Ensures maximum cooling output and long compressor life.

7. Pressure Testing, Vacuuming & Gas Check

For all 3 AC units:

• Line pressure test

• Vacuuming for moisture removal

• Checking gas levels

• Advising if gas top-up is required

• Ensuring correct refrigerant flow

8. Final Cooling Performance Test (3 AC Units)

We run performance tests on each installed unit:

• Temperature drop check

• Airflow & throw test

• Coil performance

• Noise & vibration check

• Drain flow test

• Operational stability check

All 3 ACs must pass the quality test before handing over.

What We Need From You

• Suitable space for 3 floor standing AC units

• Adequate outdoor space for 3 ODUs

• Access to electrical point

• Drainage access

• Information about any previous AC setup

• Clear pathway for moving heavy tower units

Our Service Promise

• Installation of 3 tower AC units in a single visit

• Experienced commercial AC technicians

• Brand-standard installation

• Leak-proof piping & secure wiring

• Clean and organized work

• Transparent material & labor charges

Frequently asked questions

Q1. Do you install 3 floor standing ACs in the same visit?
Yes, we install all 3 units during one appointment.

Q2. Are all brands supported?
Yes, including Daikin, Blue Star, LG, Carrier, Voltas, Panasonic, Hitachi, Lloyd, Mitsubishi & more.

Q3. Is gas filling included?
No. Gas filling is optional and chargeable separately.

Q4. What if extra copper pipe is needed?
Extra materials are chargeable — technicians inform you beforehand.

Q5. How long does installing 3 AC units take?
Approximately 3–5 hours, depending on pipe routing and site complexity.